The Right Way to Refinish a Rolltop Desk

Roll top desks are such classy statement pieces in any home.  It’s so rare to find one in excellent condition.  They are notorious for being difficult to paint because you can easily gunk up the tambour (rolling portion) with paint causing it not to roll at all.  If you are lucky enough to come across one, here are some tips for a successful transformation.

You Will Need:

  • Brushes and 6″ rollers
  • Wood Filler
  • Mouse Sander with low (60) and higher (180) sanding pads.
  • Zinsser 123 Primer
  • White Paint – I used Behr Ultra in Ultra White Satin
  • Base Coat for Faux Stain – I used Behr Honey Butter Flat
  • Gel Stain – I used Minwax Gel Stain in Walnut
  • New Hardware
  • Minwax Wipe-on Polyurethane.

I stumbled upon this desk on a Facebook page that a friend was selling.  This desk was perfect to redo because the top portion comes off and the tambour just slides out making it so much easier to refinish.  The desk was structurally in great shape but the surface needed some love.

Rolltop Before

I knew I was going to sell this piece so I decided to do the surface a dark stain using my gel stain method and would paint the rest white.  I realized that the plastic sleeve on both sides that the tambour slides into was already dark brown so I tried to spray paint it white to match what would be white.  Let me save a little spray paint and a lot of frustration by telling you that was a horrible idea.

Spray Paint Rolltop

The spray paint started peeling away when I moved the tambour up and down.  It looked horrible so I spent over an hour scraping the spray paint out with a putty knife.  I decided to faux stain the interior of the top to better match the plastic sleeves as there was no easy way to change their color.

Spray painting the tambour is also a horrible idea.  Ask me how I know…

I took off the hardware and filled obvious holes, scratches and dents on the desk with wood filler.

Filler

After 48 hours of drying, I sanded the entire desk with a rough sandpaper pad (60) with my mouse sander.  Have I mentioned lately how much I love my sander?!? Below is a picture of the two of us!   (Also, wear a respirator or mask when sanding the wood filler because those tiny particles can get in your lungs…No bueno!)

SanderSanding

Sand the tambour by laying it out flat on the ground and sand as you would the rest of the desk.

SandingTambour

After sanding it was time to prime.  Once again I used Zinsser 123 water-based primer.  I just found out they made a spray paint  version which I will have to try out on my next project.  Get a nice thick coat of primer on your piece of furniture.  You’ll notice that I didn’t get any primer on the groove the tambour slides into.

Prime 1

After priming the rest of the desk, I laid the tambour over a round kitchen garbage can that was on it’s side.  I wanted to open up the creases so I could get primer in each crease between the wood slats.  I was able to do this with a thin coat of primer.

Prime Tambour

Get just enough primer to fill in the dark portion in between the wood slats.  Use your brush to wipe off any excess and wipe your brush on some paper if you have too much paint on your brush.  You have time to wipe off the excess before it dries.  What you don’t want is a thick layer of wet, drippy paint on the tambour or the paint will crack once it dries.  The Zinsser 123 Primer is perfect for this application because it is thin but clings well to the grooves while covering well.

prime 2

At this point, fill any remaining holes, dents or scratches on the rest of the desk.  You should now be able to see them easier with the piece primed.  Sand those parts after they are dry.

Halfway into this process, I realized  that this desk didn’t have any of the cute ‘card catalog’ style drawers that you so often see on these desks.  I decided to add some using some unfinished jewelry boxes I found online.

Jewelry Boxes 1Jewelry Boxes 2

I bought two for each side and glued them together with carpenter’s glue and clamped them overnight to dry.  I also pulled off the wooden knobs, filled the holes and then made holes for some cute pulls.  Make your holes before you paint because you don’t want to risk screwing up the final finish.  I then glued the drawers onto the inside of the desk using wax paper to ensure the glue didn’t seep onto the desk top.

Base Coat 1

 

I started painting the desk with the yellowish base coat on the places I would faux stain and used white on the rest.  It took a couple coats of white paint because the desk was so dark.

I used the same process on this desk as I did with the end tables in my post How To Gel Stain Wood  Here is a pic of the first coat of gel stain.  You want to leave some sections only partly covered in the first coat to make the second coat a little more translucent and “wood-grain-like” in those parts.

Gel Stain

Back to the tambour…While I let each coat of gel stain dry at least 24 hours, I laid the tambour flat on the concrete and added a thin coat of white.  Again brush off any excess.  It was still a little streaky at this point but you will touch that up towards the end

After the second and final gel stain coat, I added a coat of wipe-on polyurethane to the stained parts.  The nice thing about latex paint and polyurethane is that you know that in 10 years the finish will look the same and be just as durable.   Both finishes provide a clean, wipe-able surface that will not hold dirt easily.

I have a friend that did her entire kitchen cabinets in chalk paint and wax.  They looked fantastic but after only 6 months they looked awful because the porosity of the chalk paint held on to every speck of dirt and dust in her kitchen.  She ended up redoing them in latex shortly after.  (Getting off my soapbox now…)

After touching up the tambour one last time, I put the desk together including the main drawers, the top and the tiny drawers.  I also added new hardware to the whole desk including ‘card catalog’ style drawer pulls to the top drawers.  Didn’t they turn out cute?

Drawers

 

Desk Transformation

Rolltop Desk with Stained Top

Notice the concrete floors in the background.  We had a massive flood which I shared about in my post Beauty From Chaos: How to Find Peace in Any Situation.

Rolltop Desk with Closed Top

This desk was quite an undertaking but worth it to bring out the full potential of such a fabulous vintage piece.  Thanks for stopping by and be sure to check out my other furniture transformations!

Writing Desk Makeover

Coffee Table Reveal and a Word About Transparency

Made Over, Inside and Out – China Cabinet Transformation

 

‘Til Next Time,

signature

Rolltop Desk at www.renovatedfaith.comTheRightWayToRefinishARolltopDesk

Beauty From Chaos: How to Find Peace in Any Situation

You might remember my pristine DIY Entertainment Center that I featured on the blog a couple weeks ago.  Now marred by water damaged and covered with dust, these pieces currently sit in our garage…..entertainment-center-2Last Sunday night, we woke at midnight to our daughter screaming.  I ran into the living room to check on her, sure that I would find her in the midst of some frantic search for her mermaid doll that fell off the bed.  Apparently, her mermaid not only fell off the bed but went for a swim because she picked it up to find it was covered in water – as was most of our house!

Living Room

Two inches of water from a broken toilet valve now covered most of our home.  We sloshed through soaked carpet to try to move most of our furniture into the garage.   A company came to pull out the carpet and set up industrial fans and dehumidifiers for a week.  Carpet has been pulled up from every room,  much of our furniture is in the garage and the contents of every closet was left in a huge pile in the middle of each room in order to remove carpeting.  The wind and noise from the fans only reminded me that the state of our house was now a swirl of chaos.

For someone who likes to surround myself with order, beauty and solitude, my home quickly became a wet, concrete-laden, obstacle course of wet furniture, carpet tacks and confusion.

I had some unfinished furniture pieces in our garage and decided I needed to finish them up to make extra room.  I pulled a half-completed secretary into our living room (aka ground zero) to touch up.  This was a piece I worked on for my friend Rebecca to use as her daughter’s desk.

Secretary before

I began put the hardware on the secretary and soon a peace came over me.  The drawers had been strewn all over the house as I waited for them to dry.  It was no nice to see them finally come together to make something beautiful. I am reminded that in spite of chaos, God’s peace can still reign in our heart’s and minds – not matter the mess, no matter the struggles or disaster that surrounds us.

Priscilla’s Shirer’s The Armor of God is a Bible study that brings to light the spiritual warfare that surrounds us on a daily basis and how to combat it.  In it she states:

“Anywhere peace is lacking you can be sure the enemy is at work.”

Peace

This quote stopped me in my tracks.  I realized that my heart felt as chaotic as our household because I was allowing Satan’s lies and deception to steal my joy and contentment.

I was blaming my discontent on the state of our house but, in reality, the peace that God gives is not as the world gives. Just because I was surrounded by disorder, my heart can be calm because God can be trusted with even the messiest of situations.

The Lord recognizes that we will have hard times, but God’s overwhelming peace has the capacity to give you rest in the most turbulent of circumstances. 

So many times I have read Philippians 4:6-7.  It is a well-known verse that commonly adorns coffee mugs, picture frames and refrigerator magnets.  Unfortunately, when it comes to this verse, I often confuse familiarity with apathy.

Do Not Be Anxious

 

This is one of those powerful verses that the enemy would love for us to forget.

But how do we really experience God’s peace in the midst of horrible circumstances? 

Priscilla points out that this verse is intrinsically tied to Isaiah 26:3: “You will keep in perfect peace those whose minds are steadfast, because they trust in you.”

When we make a conscience effort to pray with thanksgiving, instead of allowing anxiety to rule our thoughts and emotions, we are expressing a firm trust in God and His care for us.  By taking this step in faith with thanksgiving, we are affirming that God has the capacity to overcome anything that life brings.

This is the key to unlocking the peace that so often alludes us…

As Priscilla Shirer says, “This kind of faith catches His attention and He response by activating His peace within us – a peace that will not only guard but also guide us by helping us to discern the direction God is leading us to take in our lives.  Note the progression: trust leads to thankfulness and gratitude activates peace.”

As I wrote in 7 Tips To Find Your Calling, let your fears and anxieties become a reminder that you have something to bring before the Lord in prayer.  When we trust our situation to God by submitting our concerns in prayer and thanksgiving, He will be faithful to release His peace in our lives.  Before you know it you will to see the beauty of his plans even in the midst of chaos.

My prayer is that your every anxious thought would filter through this truth leaving you with the peace that only He can give.

Even in the aftermath of the flood, I was able to complete this secretary.  If you look closely, you can see concrete floors in the background.  What a testimony to how God brings beauty from ashes, growth from decay, and hope from destruction.

aquagraysecretary

secretary2

Enjoy some of the pictures of the finished secretary!  If you liked this post, you might also like:

DIY Faux Painted Signs (Free Scripture Printables)DIY Faux Painted Signs (Free Scripture Printables)

When Anxiety Knocks and God Answers, Part 1

‘Til Next Time,

signature

When Peace is Lacking

 

DIY Custom Curtain Rods

The curtain rods in our new house looked like something out of a 1960 Sears catalog and they had to go.  Knowing I had 16 windows to buy for, I realized the cost would add up fast for something so simple.  Since I wanted to spend more money on curtains, paint and accessories, I decided to figure out a way to make my own rods.

We moved into our house a year ago knowing we had lots of projects ahead.  Every room was crying out for a makeover, but honestly, I wouldn’t have it any other way.  Making curtain rods was another opportunity to put our own touch on a house we love so much.

simple-pin-final

What You Will Need:

Electrical Conduit (I used ½ inch which is actually ¾ in. in diameter)

Cabinet Knobs

Pipe Cutter

Spray Paint (I used Rustoleum Universal in Oil Rubbed Bronze)

Curtain Brackets

Electrical Tape

Super Glue (Gel is best for this)

4” screws with a Flat Head

Hot Glue (optional)

Rod Connectors for Bay Window Rods (optional)

conduit-in-lowes

First, go to the electrical section in your favorite home improvement store for electrical conduit.  I had thought about using wood dowels, but you would see the wood grain when it was spray painted.  PVC was another option, but it was too flexible, which is why electrical conduit was the perfect choice.

Electrical conduit is my new best friend.  Not only is it durable, and easy to cut, but it is also extremely cheap.  An 8’ piece of 1/2” electrical conduit will run you less than $3.00!  Be sure to pick conduit that is straight as some can be a little bent.

The best deal I found on curtain rod brackets were at Home Depot.  Make sure your bracket will fit your rod diameter.  These worked nicely with the ½” conduit.

mark-it-final

Assuming you already have curtains, measure for your brackets to match your curtain length (don’t forget to account for the height of the rings and clips if you use them).   I needed new curtains in the whole house so I put the brackets where I wanted the rods before even making the curtains.  I bought 110” curtains at Target because I decided that re-hemming Target curtains was cheaper and easier than making new ones from scratch.

Measure the desired width of your rod and add at least 4 to 6 inches so it extends a couple inches past your window on both sides.  In several cases, I extended my rods over a foot on each side of my windows.  I did this to make the window look larger than it actually is.

Notice how small this window is but it looks much larger when I extended the curtains out as far as they would go.  It also lets more light in which is always a good thing!

Mark the new rod size with a pencil so you know where to cut.  To cut the rod, you simply tighten the pipe cutter so the round blade is in line with the line you marked.  Tighten it just enough that you can still rotate it around the rod with some tension.  Keep rotating the pipe cutter around the rod until it gets loose again, tighten slightly and continue to spin it.  Do this until the groove in the rod is deep enough that the end pops off at the cut.

pipe-cutter-final

Be sure to check around to see if you can borrow a pipe cutter.  They are not very expensive but I bought one for myself, only to find out my husband already has one and my dad has two.

Now it’s time to work on the knobs.  For the bay window in the kitchen, I wanted the look of these round glass finials at Restoration Hardware but wasn’t about to pay $50 a pair, especially when I would need so many.   So, I stumbled upon 30mm Glass Cabinet Knobs at Amazon for just over $1 each.  Jackpot!

Next, super glue the head of the screw to the bottom of the knob.  Trust me, it works!

I used an ample amount of super glue and used an egg carton to hold them in place as they dried.  As they dry, you will see some white residue from the glue on the base of the knob but the paint will cover that.   Let the finials dry 48 hours to be on the safe side.

Now it’s time to paint.  We saved this step until now so we didn’t ruin the paint finish when cutting the rod or gluing the knobs.

My favorite spray paint is Rustoleum Universal and I used Oil-Rubbed Bronze.    Read the directions on the can.  They are serious about those recoat times!

spray-paint-final

At the same time you paint your rod, you will also want to spray paint your finials (cabinet knobs) and any other hardware.  If I had to do this over again, I would have painted the brackets too so they are exactly the same color.

pin-square-blue

For the curtains in the dining room, I some orange knobs I found really cheap on Amazon.  Then, I just spray painted the entire knob.  For the glass knobs, I just taped off the glass sphere with blue painter’s tape before painting.

After the paint has have dried overnight, I wrapped electrical tape around the screw so it would fit snugly into the end of the conduit.  Be sure to wrap at least 2 rows of tape around screw.  This will take some trial and error as you find the right amount of tape so the finial end fits. I just kept adding tape until it was tight enough. Secure it with hot glue if that helps.

 

For the bay window rod, I used these connectors which happened to fit my curtain rods.

DIY Bay Window Curtain Rods.jpg

Below is our master bedroom curtain rod, the tie-backs for the breakfast area bay window and the rod for my daughter’s room.

 

After attaching the finials to the rods, I hung my curtains.  I repeated this project for all 16 windows in our house and estimate that I saved a minimum of $500 if I bought all Target curtain rods.  Each rod with finials and hardware cost me about $5.

square-overiew-pin-final

 

binder-rings-final

Soon on the blog, I will share my secret on how I faked pinch-pleat curtains with pleater tape, binder rings and paper clips.

If you like this post, please share it on social media.  You might also like:

Made Over, Inside and Out – China Cabinet Makeover

DIY Vanity Transformation

‘Til Next Time,

signature

complex-pin-final

There are no affiliate links in this post.

DIY Vanity Transformation

header-image-makeup-table

After living in a tiny house and sharing a small vanity with my husband, I knew I wanted a place of my own to get ready in the mornings.  Seeing the perfect location in front of a window in our master bedroom, I was excited to put a classy new vanity in front of it with the morning light streaming in.    As much as I don’t like putting on makeup, I knew sitting at this vanity would make it much more tolerable.

Now that I had built up my own expectations of this glamorous vanity table, it was time to go shopping where I find all my favorite treasures…a used furniture store.  Other than saving money, I wanted to make this piece my own.  This project took a few weeks.  As I sanded, wiped, painted and then repeated this process, my thoughts couldn’t help but to meditate on some specific ways God works in our lives much like I was working on the desk.

before-table

He Sees Us

Upon seeing this desk at the consignment shop among the many other pieces, I knew it would be perfect as a vanity table, a piece I would truly enjoy and call my own for years to come.  I had a much better purpose for this old desk and knew it had incredible potential, but it would need a serious makeover.

In the same way, God sees us through our brokenness.  In spite of the dated molding, shiny laminate surface, burnt orange stain and weird smell, I loved that sad old desk and knew I needed as my own.  Who knew something destined for a trash heap would be one of my greatest treasures.  The same could be said of us.   Because of the stain of our sin, we deserve the trash heap but God cleans us up, transforms us and prepares a perfect place for us in His Home. 

makeup-table-sun

He Redeems Us

The definition of “redeem” is “to regain possession of something in exchange for payment.”  I bought this desk for $40 and the stool for $10.  In order to transform this desk, I had to first buy it.  There was a price to be paid, even for a dirty old desk.

The same can be said of us – we are but damaged goods in need of transformation. Our sin was so much filthier than an old piece of furniture, but a much higher price would need to be paid to give us a right standing before a perfectly holy God.  God knew no amount of good works would ever be able to rectify our sinful condition so he did the extraordinary.  He pulled us out of the ruble and God had to pay the ultimate price – His one and only son.   God rescued us from sin just like I rescued the desk from its awful fate. 

makeup-table-front

He Transforms Us

God doesn’t stop there.  Upon rescuing us, He begins an amazing process of transformation because He loves us too much to just leave us alone. Upon coming to know Christ, an amazing process of renovation begins.  I wasn’t about to bring this desk into our newly decorated bedroom and use it in its current state.  Over a period of time and in several steps, a transformation had to occur.

To achieve my vision for this desk, if it was cleaned, sanded, primed, painted and new hardware was added.  Several of those steps had to be repeated to be effective and each step had to be fully finished before proceeding to the next.  When God brings us into His family, He continues to transform us to be more and more like Him through the process of sanctification.  He renews us daily knowing that sometimes the sanding of life’s trials can be difficult.  However, we are much more content and satisfied when we allow Him to work in us to fulfill the specific plans He has for us.  He breaths in us life, beauty and purpose that we never knew was possible.

backup-makeup-table

makeup-table-hardware

Process and Source List

  1. I took off the hardware and filled holes with a generous amount of Elmer’s wood filler. I then drilled new holes for the new hardware.  I also replaced some old molding with new molding from Lowe’s by using Liquid Nails for wood.
  2. After letting the filler dry for 48 hours, I started the sanding process. I used my mouse sander to sand with rough sandpaper to remove that laminate gloss and I just sanded the legs as best as I could by hand.
  3. After wiping with a damp cloth, I primed the whole piece with Zinnser 123 water based primer and let it dry 4 hours. (It dries fast but not as fast as other primers.  This is helpful because it leaves a smoother finish).
  4. I sanded again with smoother sand paper on my mouse sander and sanded the legs by hand.
  5. After wiping with a damp cloth again, I used the Home Depot brand 6 inch rollers (“Best” with the green line) because it gives you a really smooth finish. I applied two coats of Behr Blue Fox in a satin finish with Floetrol (added according to the instructions on the back).  This helps the paint to settle better, leaving fewer brush strokes.
  6. This is the key for a really smooth – I LIGHTLY sanded yet again but with 320 sandpaper. After wiping down the desk and vacuuming the room, I applied one more coat. (Make sure fans and the AC is off to avoid dust particles in the air from settling on the paint surface.)
  7. After letting the piece dry for 2 days, I added the new hardware (amazon.com) and the glass top. Who knew the desk could look so different!?!

small butterfly frame

I thought my DIY butterfly frame was a perfect accessory for my vanity.  I posted here about how I made it and what butterflies mean to me.

wall flowers

This is a sneak peak of my Master Bedroom transformation that I’ll be posting soon!

If you enjoyed this post, you might also like these as well:

Light and Airy Master Bathroom

Made Over, Inside and Out

 

Be sure to leave a comment below.  I love to hear your feedback!

‘Til Next Time,

signature

before-after-makeup-table

Light and Airy Master Bath Makeover

Of all the rooms in our house that needed a makeover, the master bath was the worst.  Underneath that purple-hued, mauve paint and brass towel bars was a room crying out for renovation. I knew this would be my “sanctuary” at the end of the day so I wanted it to be light, airy and peaceful.

fullvanity

This isn’t just bad photography.  After staring at the sad state of our bathroom for months, I knew I couldn’t procrastinate any longer.   Notice the taupe cabinets, trim and door that had just a tint of mauve to coordinate  with the mauve walls.

horizontal before

Our house was built in the 1996, the same year this mirror and fixture were installed.  Is it me or does this picture make anyone else nervous?  It reminds me of one of those pics going around the internet where a ghost decided to reveal itself.  I think the light fixture is just as scary though.

The first task was to paint all the cabinetry, door and trim.  This was quite an undertaking but using Floetrol in my paint (Behr semigloss in pure white) helped the paint to settle well for a smooth finish.  I used this roller which is the best I have found for trim and cabinetry. Look for the roller with green lines.

lighting before

I procrastinated on this project because I knew I had possibly met my match – the shower frame!  The 20-year-old shower had horrible corrosion and no matter how much I cleaned it, that nasty shower frame still looked as gross as the first day I saw it.

Our ideal solution was to replace the shower completely with a frameless shower but we needed room in our budget for the countless other projects on our my list.    Making the shower painless to look at was my objective and I think I achieved it.  To attain this lofty goal, I reached for one of my favorite tools in my DIY arsenal – spray paint!  Yes, I decided I would spray paint the shower frame.   It only cost $80, which included spray paint and blue painters tape, but it was pretty work intensive.

shower

 

After committing to the idea, I removed all the old caulk (fun times!) and taped off with newspaper all the glass and surrounding tile.  I did not tape or cover the shower floor because any spray paint will be really easy to scrub up with soap and water, right?   WRONG!

The difficult part of this project is that you MUST cover every single square inch of your bathroom with tape, newspaper, old sheets, etc.  What you don’t cover will have a fine black powder adhered to the surface.  This is a great project to do right before you replace your flooring, like we did.

After covering and taping everything but the shower frame, I put on my respirator and started spraying the frame with automotive primer. (You have to have a respirator for this project and open all windows.  The smell dissipates quickly but its intense during the process.)

The primer wasn’t completely necessary but I wanted good adhesion to the corroded parts of the frame.  Then, I sprayed with three coats of Rustoleum Universal spray paint in Oil-Rubbed Bronze.  24 hours later I took down the sheets that I could, but I waited a full 48 hours before taking the tape off around the frame.

Be sure to score the frame edge with an exacto-knife before you take off the tape.  There were a couple places I had to touch up with spray paint remover as the spray paint got everywhere but overall it turned out better than I thought.  We will eventually get a frameless shower but this will work for now.  Rebar and Kallie seem happy with it.

vanity side view

The next task at hand was to paint the mauvish-brown trim and walls.  For the walls, I decided on Behr Ozone in Satin to achieve a relaxed, spa-like feel.

over tub

After contemplating what to hang on the wall over the bathtub, I knew whatever I displayed should be relaxing and enjoyable for the end of a long day.    Although a flat screen tv was very tempting, I decided to frame some verses that meant a lot to Jeremy and I.  We each picked two and I wrote more about what these verses mean to us and the process in a previous post.

after wall

We replaced the builder-grade mirror with two framed mirrors to give the area more interest.  The light fixtures, faucets and new knobs in satin nickel made the space more sophisticated. Notice how much better the shower looks bellow.

before after

Did I mention we built a door too?  Actually Jeremy built and hung it and I finished it with two coats of Gel stain in Minwax Walnut.  It was a nice alternative to taupe bifold doors with brass knobs.

door

I had a lot of fun accessorizing.  I made some basic white curtains out of sheets from Walmart (cheapest sheer material you will ever find).  I also enjoyed decorating with some apothecary jars and old silver of my mom’s.  It is amazing what a little silver polish can do!

As I mentioned, the framed wall verses mean a lot to me.  I picked this verse in particular because it is the heartbeat of my blog.  No matter how many or few read it, I want every word, picture and project to reflect the renovation He has done in my life.  He has fully transformed me from the inside out and I’m so thankful for His great love for us.

single pic

pinterest lead bathroom

So what do you think? Do you like it? I’m pretty happy with the way it turned out, and more importantly, it did not break the bank. And now that I have the bathroom done, I can start working on the bedroom again. Hopefully I will have another reveal for you soon.

If you like this reveal, you might also enjoy my Landscape Makeover.

Thanks so much for stopping by. I always appreciate your visits and sweet comments. Have a great day!

signature

Source List:

  • Mirrors – Target.com
  • Light Fixtures – Lowes
  • Pictures Frames – Target
  • Sink Fixtures – Home Depot

 

 

Made Over, Inside and Out

On the way home one night, I saw a very tall object on the curb of a neighbor’s house.  I drove by and in my rearview, I realized it was a large piece of furniture someone was throwing out.  We were almost home but the more I thought about it, the more I wanted another look.  We circled around and it was a dingy oak china cabinet.  Several of the doors were broken, it was dirty and even had water damage at the bottom.  However, I saw potential in that old piece– It was just begging me to take it home and make it new again.

So, I did what any good southern girl without a truck would do…I called my daddy.  Jeremy and my dad wielded the monstrosity into our garage that night.  I was determined to save it from its impending doom upon trash pickup the next morning.  They thought I was crazy for wanting to save this piece of furniture, but I knew it had potential to be something great.

china cabinet before

The process began…I surveyed the damage, dusted it off and cleaned it up.  I was even lucky enough to find an old mouse trap in the top (fortunately it was empty).  My dad rebuilt the broken doors, I ripped off some of the molding to replace with new and I restored one of the shelves inside.  After extensive sanding, a layer of heavy-duty primer to cover the orange-y stain, several coats of paint and multiple tubes of caulk, it now sits in my dining room as a permanent fixture in our home.  I am very satisfied with the end product and it brings me joy to think about how far it has come.

More importantly, the china cabinet serves as a reminder of how far I have come.  You see God also saw me in the darkness.  He saw that I was dirty, broken, and in a state of disrepair.  But that didn’t stop Him.  He didn’t even need to even take a second look.  Through no effort of my own, He delivered me from my sin and certain destruction through Christ’s death and resurrection.  Upon accepting Christ as my Savior, my eternal status is secure with Him.  Now, He is “renovating” me to be more and more like Him every day.  God has had to clean me up, release me from my baggage, repair my brokenness and He continues sanding my rough edges to make them smooth.

Fortunately, God never leaves a project half-done…He continually works on each one of us, shaping us to be a useful tool for Him to use.  That’s what the Christian life is.  It is a process of transformation that can only be done by His Hands.  We all have areas where we need work – whether it is anxiety, overeating, insecurity, or pride, God wants to renovate our hearts and minds.

Any home improvement project is messy and can take longer than we previously thought.  You might even uncover issues that you weren’t previously aware of and you may need to make several calls for help.   However, at the end of the project, the results are breath-taking and the struggle  is now behind you.  You have replaced this hang-up with new habits and the results are amazing.  You might even ask yourself “Why didn’t I tackle this sooner?”

That’s why I have entitled the blog Renovated Faith…The Lord helps you take off your old self and put on your new self.  You take off the lies and put on the truth.  You take off your cultural perspective and put on a biblical perspective.  You take off what you learned growing up and put on what the Bible says about your situation. Once you come to know Christ as your Savior, that is just the beginning.  You have a whole new life ahead of you.  God still has a lot of refinishing work to do on me and I invite you to join me on this journey as He gives us a makeover from the inside out.

“Behold, I am doing a new thing; now it springs forth, do you not perceive it?  I will make a way in the wilderness and rivers in the desert.”  Isaiah 43:19

china cabinet boxwood

front china cabinet

glasses

 

China Cabinet Restoration Process and Source List

  1. Dust off with a damp wrap and remove all hardware.  Replace any molding that is out of date.
  2. Start sanding. If you don’t have a palm sander like this one, it is well worth your money.  I have used it on countless projects and it’s my favorite tool!
  3. I’ve used several of Zinsser’s primers and decided on the Zinsser Bullseye 123 Waterproof Primer. It has great adhesion, cleans up easily, low odor and settles well into cracks, which is great for old oak furniture.  Also, it only takes an hour to dry before your next coat.  You can find it at Home Depot and Walmart.
  4. I used Behr Premium Plus white in Satin. It took me 2 good coats and then some touch ups.  I painted the inside back in Behr Sonata in Satin to give my white plates some contrast.
  5. I spray painted the hinges using Rustoleum’s Universal Metallic in Oil-Rubbed Bronze. It is the best oil-rubbed bronze spray paint on the market and so durable that I just used it to spray paint my metal shower frame.
  6. Caulk any cracks and replace hardware (I like Dap caulk). Amazon is a great source for basic hardware like the knobs.  We got the cabinet lighting here.

If you  have questions about the refinishing process, leave them in the comments section and I’ll answer within 24 hours.